tnt.aufbix.org cisco

cisco:asa

anonymous@undisclosed.example.com (Anonymous) — Tue, 10 Aug 2010 18:57:40 +0000

Cisco ASA Tips & Hacks Display Pre-Shared Keys in ASA Running Configuration Simple tip to see pre-shared VPN keys: CiscoASA# more system:running-configuration ASA Site-to-site VPN It doesn't matter how many times I've done this, I always forget one piece. Here's a template for the future:

cisco:bgp-config

anonymous@undisclosed.example.com (Anonymous) — Tue, 02 Jun 2009 23:52:38 +0000

Cisco BGP Config Example for Customers, Transit and Peers (taken from and give credit to punk.nether.net community!!) Due to the ease of configuring bgp, it is easy to leave out critical steps that will result in some unintended consequences. There are a number of cases that exist persistently in the routing tables where some small network is actually connecting two

cisco:bgp

anonymous@undisclosed.example.com (Anonymous) — Mon, 25 May 2009 00:35:02 +0000

Cisco BGP see also: networking, cisco, Secure BGP template for Cisco ---------- commands: closes bgp sessions clear ip bgp * Please write more coments on configurations!! router bgp 15393 no synchronization bgp dampening neighbor customer-pg peer-group neighbor customer-pg route-map customer-rm in neighbor customer-pg route-map standardout out neighbor X.X.X.A peer-group custome…

cisco:good-defaults

anonymous@undisclosed.example.com (Anonymous) — Sun, 28 Sep 2014 22:43:48 +0000

Source: recommended on 2900 series for IPv6 traffic: auto archiving on 'write memory' disable local services + add some security stuff

cisco:ipsec

anonymous@undisclosed.example.com (Anonymous) — Tue, 12 Aug 2014 15:02:54 +0000

Cisco IPSec stuff ISAKMP associations using RSA keys more detailed:

cisco:ipv6

anonymous@undisclosed.example.com (Anonymous) — Thu, 11 Nov 2010 08:49:16 +0000

Cisco related stuff and IPv6 Cisco IPv6 routing Attempting our ping again from R1 elicits the following output from the debug on R2: “Not a router?” R2(config)# ipv6 unicast-routing ipv6 unicast-routing ipv6 cef interface FastEthernet0/0 ipv6 enable ipv6 address xx:xx:xx:xx:xx::x/yy

cisco:multicasting

anonymous@undisclosed.example.com (Anonymous) — Mon, 15 Oct 2012 11:55:47 +0000

Multicasting PIM Modes In actuality, PIM refers to a family of very similar routing protocols, but which each operate in a different mode. These are: * PIM Dense Mode (PIM-DM) (RFC 3973) * PIM Sparse Mode (PIM-SM) (RFC 4601) * Bidirectional PIM (BIDIR-PIM) (

cisco:ospf

anonymous@undisclosed.example.com (Anonymous) — Mon, 25 May 2009 00:35:02 +0000

Cisco OSPF Tips & Tricks releted * OSPF Default Mysteries (IP Conrner at NIL) * OSPF Overview

cisco:pastebin

anonymous@undisclosed.example.com (Anonymous) — Sat, 17 May 2014 13:18:29 +0000

Cisco random pastebin :) See open ports R1# show control-plane host open-ports Active internet connections (servers and established) Prot Local Address Foreign Address Service State tcp *:23 *:0 Telnet LISTEN tcp *:80 *:0 HTTP CORE LISTEN tcp *:179 *:0 BGP LISTEN tcp *:179 10.0.7.2:43962 BGP ESTABLIS tcp *:23 10.0.7.2:18036 …

cisco:showinterface

anonymous@undisclosed.example.com (Anonymous) — Thu, 17 May 2012 08:36:33 +0000

Interface and Line Protocol Status Line State Possible Causes and Actions Serial x is up, line protocol is up This status indicates that the interface is functioning properly Serial x is down, line protocol is down This status indicates that the router is not sensing a carrier detect (CD) signal.

cisco:sidebar

anonymous@undisclosed.example.com (Anonymous) — Mon, 08 Nov 2010 12:11:50 +0000

See also * networking * working with cisco * Good Cisco defaults * Show Interface Reference * cisco and BGP * Cisco BGP Config Example * cisco and OSPF tips * cisco and IPSec/VPN * cisco unsorted * cisco (catalyst) switches * Cisco ASA tips * multicasting * Cisco IPv6 stuff Cisco emulators * Cisco 7200 Simulator * The network configuration generator for Dynamips * GNS3 - graphical network simulator Multihoming * IOS NAT Load-balancing for…

cisco:switch

anonymous@undisclosed.example.com (Anonymous) — Thu, 24 Nov 2011 13:34:24 +0000

GOOD TO KNOW! * ethernet broadcast packets (dest mac ff:ff:ff:ff:ff:ff) * traffic for the mac addresses learned on the port * traffic with dest. mac addresses unknown to the switch, which is flooded to all ports but the one where the packets entered.