Differences

This shows you the differences between two versions of the page.

--- openswan [2012/05/18 11:13]
216.206.60.33 ffgftAORYO
+++ openswan [2012/05/18 13:17] (current)
greebo old revision restored
@@ Line 1: / Line 1: @@
-IqsLG , [url=http://kywwfraotins.com/]kywwfraotins[/url], [link=http://inzzdwbqbofc.com/]inzzdwbqbofc[/link], http://tmkucdoqhahx.com/
+====== Openswan ======
+ex FreeSWAN - IPSec kernel stack and userspace ipsec tools for linux
+see: [[http://www.openswan.org|Openswan main page]], [[http://wiki.openswan.org|Openswan's Wiki]]
+===== ipsec.secrets =====
+<code |f ipsec.secrets>
+x.x.x.x
+	x.x.x.x	%any:	PSK "<secretkeygoeshere>"
+: RSA	{
+        # RSA 2048 bits   erwin   Tue Apr  1 19:54:25 2008
+        # for signatures only, UNSAFE FOR ENCRYPTION
+        #pubkey=0sAQOLURatBjxUM9StRL7M0++UoZTAsbmMa5ucAb.....
+</code>
+===== OpenSWAN + Cisco PIX =====
+   version 2.0
+   config setup
+          interfaces=%defaultroute
+          klipsdebug=all #enable debugging
+          plutodebug=all
+   conn tunnelipsec
+          type=tunnel     #tunnel mode ipsec
+          left=x.x.x.x   #the IP address of your OpenSWAN endpoint
+          leftnexthop=y.y.y.y   #default gateway
+          leftsubnet=10.0.0.0/8   # network behind your endpoint
+          right=%any   # Your IP, or %any for a road-warrior setup
+          rightnexthop=%defaultroute    #defaultroute for road warrior unknown
+          rightsubnet=10.2.0.0/16    #network behind the PIX
+          esp=3des-sha1    #esp: 3des, hmac: sha1
+          keyexchange=ike    #use regular ike
+          authby=secret    #pre-shared secret,  you can also use rsa nounces
+          pfs=yes    #use perfect forward secrecy
+          auto=add     #don't initiate tunnel, but allow incoming
+         spi=0x0    #use base spi of 0x0 for PIX
+PIX setup
+   sysopt connection permit-ipsec
+   crypto ipsec transform-set vpnset esp-3des esp-sha-hmac
+   crypto map vpnmap 10 ipsec-isakmp
+   crypto map vpnmap 10 match address 108
+   crypto map vpnmap 10 set peer x.x.x.x
+   crypto map vpnmap 10 set transform-set vpnset
+   crypto map vpnmap 10 set pfs group2
+   crypto map vpnmap interface outside
+   isakmp enable outside
+   isakmp key ******** address x.x.x.x netmask 255.255.255.255 no-xauth no-config-mode
+   isakmp identity address
+   isakmp policy 5 authentication pre-share
+   isakmp policy 5 encryption 3des
+   isakmp policy 5 hash sha
+   isakmp policy 5 group 2
+   isakmp policy 5 lifetime 3600
+   nat (inside) 0 access-list 108
+   access-list 108 permit ip 10.2.0.0 255.255.0.0 10.0.0.0 255.0.0.0