Cisco vs. Juniper

Command list

Cisco Command Juniper Command Co-Ordinating Definition
show ip interface brief show interface terse displays the status of interfaces configured for IP
show interface [intfc] show interfaces [intfc] detail displays the interface configuration, status and statistics.
show controller intfc show interfaces intfc extensive displays information about a physical port device
show interface / incl (proto/Desc) show interfaces description displays the interface configuration, status and statistics
show ip route show route displays summary information about entries in the routing table
show ip bgp summary show bgp summary displays the status of all Border Gateway Protocol (BGP) connections
show ip bgp net mask show route protocol bgp prefix will show you how that route is being advertised, look for the first line
show ip bgp net mask longer-prefixes show route range prefixwill show you how that route is being advertised, look for the first line
show ip bgp regexp AS-regexp show route aspath-regexp “AS-regexp” displays routes matching the autonomous system (AS) path regular expression
show ip bgp neighbors neigh received-routesshow route receive-protocol bgp neigh / show route source-gateway neigh protocol bgp Shows whether a neighbor supports the route refresh capability
show ip bgp neighbor neigh advertised-routesshow route advertising-protocol bgp neighShows whether a neighbor supports the route refresh capabilty
show clns neighborsshow isis adjacencydisplays both ES and IS neighbors
show clns interfaceshow isis interfaceshows specific information about each interface
show ip route isisshow isis routesdisplays the current state of the the routing table
show isis topologyshow isis spfdisplays a list of all connected routers in all areas
show ip ospf interfaceshow ospf neighbor shows neighbor ID, Priority, IP, & State if the neighbor router, dead time.
show ip ospf interfaceshow ospf interface shows neighbor id, pri, state, dead time, address and interface
show ip route ospf show ospf route display the current state of the routing table
show ip ospf database show ospf database display list of information related to the OSPF database for a specific communication server
show version show version, show system uptime display the system hardware config., software version, and name and source of configuration files and boot images
show diags show chasis hardware displays power-on diagnostics status
show processes cpu show system process displays utilization statistics
show tech-support request support info displays the current software image, configuration, controllers, counters, stacks, interfaces, memory and buffers
show logging show log messages display the state of logging to the syslog
show route-map name show policy name displayall route-maps configured or only the one specified
show ip prefix-list name show policy name display information about a prefix list or prefix list entries
show ip community-list list configure, show policy-options community name display routes that are permitted by BGP community list
show environment all show chassis environment displays temperature and voltage information on the console
ping dest ping dest rapid (for cisco like output) / ping dest (for unix like output) to check to see if a destination is alive
ping (setting source int) ping dest bypass-routing to check to see if a destination is alive
terminal monitor monitor start messages Change console terminal settings
terminal no monitor monitor stop Change console terminal settings
terminal length 0 set cli screen-length 0 sets the length for displaying command output

OSPF

Some subtle differences Because OSPF has several checks and balances in regards to neighbor adjacencies, and because those adjacencies are essential for actual routing, their defaults remain the same between the two vendors. These include authentication (except in the case of OSPFv3), hello/dead intervals and area types. One note about authentication: in Cisco IOS when area authentication (either MD5 or Simple) is configured at the protocol level it triggers the bit in the AuType field within the header. This means that without a like configuration on neighboring routers, adjacencies will not be created. Juniper does not, at the protocol level, trigger the AuType bit unless the key is configured within the interface.

In the examples below, both configurations will change the AuType to 2 which would satisfy one of the adjacency requirements. Of course if we were trying to get these two to “neighbor-up” it wouldn't work.

Cisco Example

 router ospf 1
 area 0.0.0.0 authentication message-digest
 end

Juniper Example

 protocols ospf {
      area 0.0.0.0 {
           authentication-type md5;
      interface ge1/0/1.0{
           authentication  {  
                md5 1 key juniper;
   }
   } 
   }
 }

Another difference lies within the functions of stub ABRs. This is a classic difference between routers made for enterprise operations and routers made for the provider industry. In Cisco IOS a stub router which is configured to either allow summary route or inject just one summary (totally stubby) will do just that. In Juniper land, that particular function is optional and must be configured using the “default-metric” command.

On broadcast/multi-access media such as Ethernet, OSPF elects a Designated Router (DR) to act as the originator of network advertisements and synchronizing of link-state databases. The election process involves the comparison of OSPF priority values and Router-IDs. On a data link the highest priority wins the election. Each vendor has a default priority and each vendor recognizes that a priority of 0 does not allow that interface to be considered in an election. Cisco has a default priority of 1 and Juniper has a default of 128. This means of course, that if you put Cisco and Juniper on the same broadcast segment, Juniper will by default become the designated router.

networking/cisco-juniper.txt · Last modified: 2009/05/25 00:35 (external edit)
CC Attribution-Share Alike 4.0 International
Driven by DokuWiki Recent changes RSS feed Valid CSS Valid XHTML 1.0 ipv6 ready