Differences
This shows you the differences between two versions of the page.
networking:cisco-juniper [2007/10/30 13:55] a created |
networking:cisco-juniper [2009/05/25 00:35] |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ^ Cisco Command ^ Juniper Command ^ Co-Ordinating Definition ^ | + | |
- | | show ip interface brief | show interface terse | displays the status of interfaces configured for IP | | + | |
- | | show interface [intfc] | show interfaces [intfc] detail | displays the interface configuration, | + | |
- | | show controller intfc | show interfaces intfc extensive | displays information about a physical port device | | + | |
- | | show interface / incl (proto/ | + | |
- | |show ip route |show route |displays summary information about entries in the routing table | | + | |
- | |show ip bgp summary |show bgp summary | displays the status of all Border Gateway Protocol (BGP) connections | | + | |
- | |show ip bgp net mask |show route protocol bgp prefix | will show you how that route is being advertised, look for the first line| | + | |
- | |show ip bgp net mask longer-prefixes| show route range prefix|will show you how that route is being advertised, look for the first line| | + | |
- | |show ip bgp regexp AS-regexp |show route aspath-regexp " | + | |
- | |show ip bgp neighbors neigh received-routes|show route receive-protocol bgp neigh / show route source-gateway neigh protocol bgp |Shows whether a neighbor supports the route refresh capability| | + | |
- | |show ip bgp neighbor neigh advertised-routes|show route advertising-protocol bgp neigh|Shows whether a neighbor supports the route refresh capabilty| | + | |
- | |show clns neighbors|show isis adjacency|displays both ES and IS neighbors| | + | |
- | |show clns interface|show isis interface|shows specific information about each interface| | + | |
- | |show ip route isis|show isis routes|displays the current state of the the routing table| | + | |
- | |show isis topology|show isis spf|displays a list of all connected routers in all areas| | + | |
- | |show ip ospf interface|show ospf neighbor |shows neighbor ID, Priority, IP, & State if the neighbor router, dead time.| | + | |
- | |show ip ospf interface|show ospf interface |shows neighbor id, pri, state, dead time, address and interface| | + | |
- | |show ip route ospf |show ospf route |display the current state of the routing table| | + | |
- | |show ip ospf database |show ospf database |display list of information related to the OSPF database for a specific communication server| | + | |
- | |show version |show version, show system uptime |display the system hardware config., software version, and name and source of configuration files and boot images| | + | |
- | |show diags |show chasis hardware |displays power-on diagnostics status| | + | |
- | |show processes cpu |show system process |displays utilization statistics| | + | |
- | |show tech-support |request support info |displays the current software image, configuration, | + | |
- | |show logging |show log messages |display the state of logging to the syslog| | + | |
- | |show route-map name |show policy name |displayall route-maps configured or only the one specified| | + | |
- | |show ip prefix-list name |show policy name |display information about a prefix list or prefix list entries| | + | |
- | |show ip community-list list |configure, show policy-options community name |display routes that are permitted by BGP community list| | + | |
- | |show environment all |show chassis | + | |
- | |ping dest |ping dest rapid (for cisco like output) / ping dest (for unix like output) |to check to see if a destination is alive| | + | |
- | |ping (setting source int) |ping dest bypass-routing |to check to see if a destination is alive| | + | |
- | |terminal monitor |monitor start messages |Change console terminal settings| | + | |
- | |terminal no monitor |monitor stop |Change console terminal settings| | + | |
- | |terminal length 0 |set cli screen-length 0 |sets the length for displaying command output| | + |