[[linux:firewall]]
Trace:
Show page
AdminRecent ChangesSitemap

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
Last revision Both sides next revision
linux:firewall [2010/12/29 10:16]
greebo 		linux:firewall [2016/02/23 10:51]
zagi
Line 2: Line 2:
 [[linux:firewall_blocktor| how to block TOR network in realtime]]\\  [[linux:firewall_blocktor| how to block TOR network in realtime]]\\ 
 [[http://www.fs-security.com/|FS security]]\\ [[http://www.fs-security.com/|FS security]]\\
- 
  
 <code bash |> <code bash |>
Line 27: Line 26:
  
 # path to iptables and iproute2 files # path to iptables and iproute2 files
- 
 IPTB="/sbin/iptables" IPTB="/sbin/iptables"
 IP="/sbin/ip" IP="/sbin/ip"
  
 # name of our Internet and intranet interfaces # name of our Internet and intranet interfaces
-# 
 # use INTRANET="eth1+" or INTERNET="eth0+" # use INTRANET="eth1+" or INTERNET="eth0+"
 # if you have more ifaces (example: eth0:0)  towards Intranet/Internet # if you have more ifaces (example: eth0:0)  towards Intranet/Internet
-INTRANET="eth1"+# 
 +# WAN Interface
 INTERNET="eth0" INTERNET="eth0"
 # ADSL - INTERNET="ppp0" # ADSL - INTERNET="ppp0"
 +#
 +# LAN Interface
 +INTRANET="eth1"
      
 # what IPs are used in intranet # what IPs are used in intranet
Line 65: Line 66:
 212.18.32.0/24" 212.18.32.0/24"
  
 +# enable IP forwarding (routing!)
 echo "0" > /proc/sys/net/ipv4/ip_forward echo "0" > /proc/sys/net/ipv4/ip_forward
 +
 +# enable PMTU (mss/mtu discovery)
 +echo "1" > /proc/sys/net/ipv4/tcp_mtu_probing
  
 # first we flush the tables and policy # first we flush the tables and policy
Line 102: Line 107:
         $IPTB -A ssh-access -s $sshhostese -j ACCEPT         $IPTB -A ssh-access -s $sshhostese -j ACCEPT
         done         done
- # Connection limit for SSH connections (1 connection per minute) - usefull against ssh scanners if you MUST open SSH for every IP! + # Connection limit for SSH connections (1 connection per minute PER source IP) 
- # it is wise to use sshaccess input table (TRUSTED_HOSTS) + # - usefull against ssh scanners if you MUST open SSH for every IP! 
-$IPTB -A ssh-access -m limit --limit 1/minute --limit-burst 1 -j ACCEPT+$IPTB -A ssh-access -m hashlimit --hashlimit 1/minute --hashlimit-burst 1 --hashlimit-mode srcip --hashlimit-name ssh -j ACCEPT
 $IPTB -A ssh-access -j DROP $IPTB -A ssh-access -j DROP
 # ssh # ssh
Line 121: Line 126:
  
 # we allow all traffic from $INTRANET and localhost interfaces # we allow all traffic from $INTRANET and localhost interfaces
-$IPTB -A INPUT -i $INTRANET -j ACCEPT +$IPTB -A INPUT -i $INTRANET -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT 
-$IPTB -A INPUT -i lo -j ACCEPT+$IPTB -A INPUT -i lo  -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT
  
-#$IPTB -A INPUT -m state --state INVALID -m limit --limit 1/minute -j LOG --log-prefix "INVALID packet> " +$IPTB -A INPUT -m state --state INVALID -m limit --limit 1/minute -j LOG --log-prefix "packet not in conntrack> " 
-#$IPTB -A INPUT -m state --state INVALID -j DROP+$IPTB -A INPUT -m state --state INVALID -j DROP
  
 # #
Line 132: Line 137:
    
 #FIN is set and ACK is not #FIN is set and ACK is not
-$IPTB -A INPUT -p tcp --tcp-flags ACK,FIN FIN -j DROP 
 $IPTB -A INPUT -p tcp --tcp-flags ACK,FIN FIN -j LOG --log-prefix "FIN> " $IPTB -A INPUT -p tcp --tcp-flags ACK,FIN FIN -j LOG --log-prefix "FIN> "
 +$IPTB -A INPUT -p tcp --tcp-flags ACK,FIN FIN -j DROP
  
 #PSH is set and ACK is not #PSH is set and ACK is not
-$IPTB -A INPUT -p tcp --tcp-flags ACK,PSH PSH -j DROP 
 $IPTB -A INPUT -p tcp --tcp-flags ACK,PSH PSH -j LOG --log-prefix "PSH> " $IPTB -A INPUT -p tcp --tcp-flags ACK,PSH PSH -j LOG --log-prefix "PSH> "
 +$IPTB -A INPUT -p tcp --tcp-flags ACK,PSH PSH -j DROP
  
 #URG is set and ACK is not #URG is set and ACK is not
-$IPTB  -A INPUT -p tcp --tcp-flags ACK,URG URG -j DROP 
 $IPTB  -A INPUT -p tcp --tcp-flags ACK,URG URG -j LOG --log-prefix "URG> " $IPTB  -A INPUT -p tcp --tcp-flags ACK,URG URG -j LOG --log-prefix "URG> "
 +$IPTB  -A INPUT -p tcp --tcp-flags ACK,URG URG -j DROP
  
 # Block portscans: # Block portscans:
Line 159: Line 164:
  
 #FIN and RST are both set #FIN and RST are both set
-$IPTB -A INPUT -p tcp --tcp-flags FIN,RST FIN,RST -j DROP 
 $IPTB -A INPUT -p tcp --tcp-flags FIN,RST FIN,RST -j LOG --log-prefix "fin/rts flag>" $IPTB -A INPUT -p tcp --tcp-flags FIN,RST FIN,RST -j LOG --log-prefix "fin/rts flag>"
 +$IPTB -A INPUT -p tcp --tcp-flags FIN,RST FIN,RST -j DROP
  
-$IPTB -A INPUT -f -j LOG --log-prefix "FRAGMENT> "+$IPTB -A INPUT -f -j LOG --log-prefix "Lost FRAGMENT> "
 $IPTB -A INPUT -f -j DROP $IPTB -A INPUT -f -j DROP
  
Line 184: Line 189:
 for i in $TCP_PORTS for i in $TCP_PORTS
  do  do
- $IPTB -A INPUT -p tcp -m state --syn --state NEW  --dport $i -j ACCEPT+ $IPTB -A INPUT -p tcp -m state --syn --state NEW  --dport $i -j ACCEPT
         done         done
  
Line 193: Line 198:
 $IPTB -A INPUT -p tcp --dport 113 -j REJECT --reject-with tcp-reset $IPTB -A INPUT -p tcp --dport 113 -j REJECT --reject-with tcp-reset
  
-# traceroute+# traceroute (udp - IOS, Uni*es)
 $IPTB -A INPUT -p udp -m limit --limit 3/second  --sport 32769:65535 --dport 33434:33523 -j ACCEPT $IPTB -A INPUT -p udp -m limit --limit 3/second  --sport 32769:65535 --dport 33434:33523 -j ACCEPT
  
 # Log and drop ICMP fragments (shouldn not happen at all, but often used for DoS) # Log and drop ICMP fragments (shouldn not happen at all, but often used for DoS)
 $IPTB -A INPUT -i $INTERNET --fragment -p icmp -j LOG --log-prefix "Fragmented incoming ICMP> " $IPTB -A INPUT -i $INTERNET --fragment -p icmp -j LOG --log-prefix "Fragmented incoming ICMP> "
-$IPTB -A INPUT -i $INTERNET --fragment -p icmp -j DROP+$IPTB -A INPUT -i $INTERNET --fragment -p icmp -m hashlimit --hashlimit 10/second --hashlimit-burst 1 --hashlimit-mode srcip --hashlimit-name icmp-frag -j ACCEPT
  
 # thou shall NOT block ALL ICMP, but only allow usefull ICMP types to pass trough # thou shall NOT block ALL ICMP, but only allow usefull ICMP types to pass trough
-$IPTB -A INPUT -p icmp --icmp-type 0  -m limit --limit 30/second -j ACCEPT +# echo-reply 
-$IPTB -A INPUT -p icmp --icmp-type 3  -m limit --limit 30/second -j ACCEPT +#$IPTB -A INPUT -p icmp --icmp-type 0 -m hashlimit --hashlimit 10/second --hashlimit-burst 1 --hashlimit-mode srcip --hashlimit-name icmp0 -j ACCEPT 
-$IPTB -A INPUT -p icmp --icmp-type 4  -m limit --limit 30/second -j ACCEPT +$IPTB -A INPUT -p icmp --icmp-type 3 -m hashlimit --hashlimit 10/second --hashlimit-burst 1 --hashlimit-mode srcip --hashlimit-name icmp3 -j ACCEPT 
-$IPTB -A INPUT -p icmp --icmp-type 11 -m limit --limit 30/second -j ACCEPT +#$IPTB -A INPUT -p icmp --icmp-type 4 -m hashlimit --hashlimit 10/second --hashlimit-burst 1 --hashlimit-mode srcip --hashlimit-name icmp4 -j ACCEPT 
-$IPTB -A INPUT -p icmp --icmp-type 12 -m limit --limit 30/second -j ACCEPT+$IPTB -A INPUT -p icmp --icmp-type 11 -m hashlimit --hashlimit 10/second --hashlimit-burst 1 --hashlimit-mode srcip --hashlimit-name icmp11 -j ACCEPT 
 +$IPTB -A INPUT -p icmp --icmp-type 12 -m hashlimit --hashlimit 10/second --hashlimit-burst 1 --hashlimit-mode srcip --hashlimit-name icmp12 -j ACCEPT
 #icmp-traceroute #icmp-traceroute
-$IPTB -A INPUT -p icmp --icmp-type 30 -m limit --limit 30/second -j ACCEPT +$IPTB -A INPUT -p icmp --icmp-type 30 -m hashlimit --hashlimit 10/second --hashlimit-burst 1 --hashlimit-mode srcip --hashlimit-name icmp30 -j ACCEPT
 # echo-request # echo-request
-$IPTB -A INPUT -p icmp --icmp-type 8  -m limit --limit 3/second -j ACCEPT+$IPTB -A INPUT -p icmp --icmp-type 8 -m hashlimit --hashlimit 10/second --hashlimit-burst 1 --hashlimit-mode srcip --hashlimit-name icmp8 -j ACCEPT
  
 # if the default policy is not DROP then we must use this # if the default policy is not DROP then we must use this
Line 231: Line 236:
 $IPTB -A FORWARD -m state --state INVALID -j DROP $IPTB -A FORWARD -m state --state INVALID -j DROP
 $IPTB -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT $IPTB -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT
-$IPTB -A FORWARD -m state --state NEW -i ! $INTERNET -j ACCEPT+$IPTB -A FORWARD -m state --state NEW ! -i $INTERNET -j ACCEPT
  
 $IPTB -A FORWARD -m pkttype --pkt-type broadcast -j DROP $IPTB -A FORWARD -m pkttype --pkt-type broadcast -j DROP
Line 243: Line 248:
  
 # ADSL (PPPoE connections) # ADSL (PPPoE connections)
-#$IPTB -I FORWARD --protocol tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu+#$IPTB -I FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu
 $IPTB -I FORWARD -o $INTERNET -p tcp --tcp-flags SYN,RST SYN -m tcpmss --mss 1400:1536 -j TCPMSS --clamp-mss-to-pmtu $IPTB -I FORWARD -o $INTERNET -p tcp --tcp-flags SYN,RST SYN -m tcpmss --mss 1400:1536 -j TCPMSS --clamp-mss-to-pmtu
  
Line 257: Line 262:
      
 # list the rules # list the rules
-$IPTB -L -v -n+$IPTB -L -v -n --line 
 +$IPTB -t nat -L -v -n --line
      
 echo $WE_HAVE_INTRANET > /proc/sys/net/ipv4/ip_forward echo $WE_HAVE_INTRANET > /proc/sys/net/ipv4/ip_forward
  
 </code> </code>
linux/firewall.txt · Last modified: 2019/04/15 10:18 by zagi
Show pageOld revisions
Media ManagerBack to top
CC Attribution-Share Alike 4.0 International
Driven by DokuWiki Recent changes RSS feed Valid CSS Valid XHTML 1.0 ipv6 ready